|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
INFRARED RECEIVER MODULE Description The MIM-R1AA38-1 series are 37.9 KHZ miniaturized infrared receivers for remote control and other appplications requiring improved ambient light rejection. The separate PIN diode and preamplifier IC are assembled on a single leadframe. The epoxy package contains a special IR filter. This module has excellent performance even in disturbed ambient light applications and provides protection against uncontrolled output pulses. MIM-R1AA38-1 Package Dimensions MIM-R1AA38-1 Features l l l l l l unit : mm Photo detector and preamplifier in one package Internal filter for PCM frequency High immunity against ambient light 12.50.4 100.3 CENTER OF SENSOR Improved shielding against electric field disturbance 5-Volt supply voltage; low power consumption 30.60.52 9.20.5 0.8max. 0.65 1.40.3 1 2 3 0.40.05 TTL and CMOS compatibility 1 Vout 2 3 2.54 0.50.05 40.3 5.80.3 GND Vcc 5.08 Notes : 1. Tolerance is 0.25 mm (.010") unless otherwise noted. 2. Lead spacing is measured where the leads emerge from the package. BLOCK DIAGRAM ABLC V AM TRAP BPF TRIMMIN G Output fo GND Unity Opto Technology Co., Ltd. 07/26/2000 P1 MIM-R1AA38-1 Absolute Maximum Ratings Item Supply voltage Operating temperature Storage temperature Soldering temperature Power Dissipation Symbol VCC Topr Tstg Tsd PD Ratings 5.8 -10 ~ + 60 -20 ~ + 75 260 17.5 Unit V C C C mW Maximum 5 seconds @ TA=25C Remark Vcc=+5.0V ; under no signal Electro-optical characteristics (Vcc=5V) Parameter Current consumption Response wavelength Tuning frequency Output form H level output voltage L level output voltage H level output pulse width L level output pulse width Distance between emitter &detector @ TA=25C Typ. Max. 5.0 940 37.9 Unit mA nm KHZ Remarks Under no signal Symbol Icc p f0 Min. - - - - - active low output - - - - V0h V0l Twh Twl L 400 400 10.0 16 55 4.2 0.5 800 800 m deg V V s s Note 1 Horizonal direction Half angle Test Method A. Standard Transmitter ON/OFF pulse width satisfied from 20 cm to detection limit carrier frequency f0 duty 50% 600s 600s 600s Fig 1. Burst Wave 20cm 10k PD3516 +5v 10F 10k Transmitter Duty 50% Vout Oscilloscope Fig 2. Standard Transmitter Measurement circuit Unity Opto Technology Co., Ltd. 07/26/2000 P2 MIM-R1AA38-1 B. Detection Length Test Transmitter output L D.U.T Vout : indicates horizontal and vertical directions C. Pulse Width Test Transmitter output 600s 600s DUT output pulse Twl Twh V0h V0l CHARACTERISTIC CURVES (TA=25C) 2.8 Supply Current Icc (mA) 2.7 2.6 2.4 2.2 2.0 Input Level VIN (mVP-P) 400 2 3 6 4 5 Supply Voltage Vcc (V) 7 8 0.1 1 10 Input Level (mVp-p) 100 1000 Output Pulse Width tPW(s) 900 800 700 600 500 Burst length * 600s, cycle = 1.2ms tpw: Average value of output from start of signal input to 60th pulse SUPPLY VOLTAGE vs. SUPPLY CURRENT INPUT LEVEL vs.OUTPUT PULSE WIDTH INPUT LEVEL vs.OUTPUT PULSE WIDTH NOTE 1. Distance between emitter & detector specifies maximum distance that output wave form satisfies the standard under the conditions below against the standerd transmitter. (1)Measuring place .........Indoor without extreme reflection of light. (2)Ambient light source... Detecting surface illumination shall be 20050Lux under ordinary hite fluorescense lamp of no high frequency lighting. (3)Standard transmitter ... Burst wave indicated in Fig 1. of standard transmitter shall be arranged to 50mVp-p under the measuring circuit specified in Fig 2. Unity Opto Technology Co., Ltd. 07/26/2000 P3 |
Price & Availability of MIM-R1AA38-1 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |